www.diyaudiovillage.net
Source & Line amp & Amplifier Project ผลงาน DIY => Vacuum Tubes => ข้อความที่เริ่มโดย: CreÃte_Lek ♫ ที่ 27 ธันวาคม 2013, 11:37:17 AM
-
EL34 (6CA7) Class B Push-Pull
(http://tube-amps.net/images/EL34_PP_01/EL34_Schematic.jpg)
Harmonic Distortion
(http://tube-amps.net/images/EL34_PP_01/EL34_HD.jpg)
Frequency Response
(http://tube-amps.net/images/EL34_PP_01/EL34_FR.jpg)
Common grid No. 2 resistor (without decoupling) 750 Ohms
Grid No. 1 bias -36 Volts
Grid No. 3 voltage 0 Volts
Input voltage 25.8 Volts
Load resistance, plate to plate 4000 Ohms
Plate supply voltage 500 Volts
Plate voltage 475 Volts
Grid No. 2 supply voltage 400 Volts
Plate current 2 x 125 mA
Grid No. 2 current 2 x 25 mA
Max. signal power output 70 Watts
Total harmonic distortion 5%
-
KT-88 Class AB1 Fixed Bias Ultra-Linear Push-Pull Data Sheet (40% Screen tap)
(http://tube-amps.net/images/KT88_PP_01/KT88_Schematic.jpg)
Harmonic Distortion
(http://tube-amps.net/images/KT88_PP_01/KT88_HD.jpg)
Frequency Response
(http://tube-amps.net/images/KT88_PP_01/KT88_FR.jpg)
Plate, Screen B Voltages: Va,g2(b) 560 Volts
Plate, Screen Voltage (0 Signal): Va,g2(0) 553 Volts
Plate + Screen Current (0 Signal): Ia+g2(0) 2 x 50 mA
Plate + Screen Current (Max Signal): Ia+g2(max sig) 2 x 157 mA
Plate to Plate Load: RL(a-a) 4,500 Ohms
Control Grid Voltage: Vg1 (approx) - 75 Volts
Power Output: Pout 100 Watts
Total Distortion: Dtot 2%
Intermodulation Distortion (60&6000Hz 4:1 Amp): I.M. 11%
Pa+g2(0) 2 x 27.5 W 2 x 22.5 W
Pa+g2 (max Signal) 2 x 33 W
Voltage between C Grids: V(g1-g1)(ac) crest 140 Volts
Zout 7,000 Ohms
-
EL84 Class AB1 Push-Pull UL Connection 43% Screen
(http://tube-amps.net/images/EL84_PP_01/EL84_Schematic.jpg)
Plate Voltage: Va 300 Volts
Screen Voltage: Vg2 300 Volts
Cathode Current (0 Signal): Ik(0) 80 mA
Cathode Current (Max Signal): Ik(max signal) 90 mA
R.M.S. Input Voltage (grid to grid): Vin(g-g) r.m.s. 16 Volts
Plate to Plate Load: Ra-a 8,000 Ohms
Power Output: Pout 11 Watts
Total Distortion: Dtot 0.7%
-
EL34 Triode Connection Non-NFB Push-Pull
(http://tube-amps.net/images/EL34_PP_NNFB_01/EL34_Schematic.jpg)
Parameters
Opt 1 Opt 2
B Voltages: Vb 400 Volts 430 Volts
Cathode Register: Rk (Common) 220 Ohms 250 Ohms
Plate Current (0 Signal): Ia(0) 2 x 65 mA 2 x 64 mA
Plate Current (Max Signal): Ia(max signal) 2 x 71 mA 2 x 67 mA
Plate to Plate Load: RL(a-a) 5,000 Ohms 10,000 Ohms
Control Grid Voltage: Vg1 (approx) - 29 Volts - 32 Volts
Power Output: Pout 16 Watts 14 Watts
Total Distortion: Dtot 3% <1%
-
[puzzled] ท่าน เจ้าสำนัก ครับแล้ว KT 120 PP ไม่มีบ้างหรือครับ หรือใช้ร่วมกับ KT 88 PP ครับ [smiling-tongue]
-
พี่เล็กมีวงจร 6ag7 * 3 หรือเปล่าครับ เผื่อเอามาลองทำกระทู้ข้างๆ
-
ก็ที่น้ารุ่งลงไว้ไงครับ
-
[puzzled] [huge-thumbs-up] ขอบคุณครับพี่
-
[puzzled] ท่าน เจ้าสำนัก ครับแล้ว KT 120 PP ไม่มีบ้างหรือครับ หรือใช้ร่วมกับ KT 88 PP ครับ [smiling-tongue]
ทำเท่าที่มีนั่นแหละอย่า ยุกยิก เดี๋ยวปะเหนี่ยวเลย [angry2-watermelon]
-
[puzzled] ท่าน เจ้าสำนัก ครับแล้ว KT 120 PP ไม่มีบ้างหรือครับ หรือใช้ร่วมกับ KT 88 PP ครับ [smiling-tongue]
ทำเท่าที่มีนั่นแหละอย่า ยุกยิก เดี๋ยวปะเหนี่ยวเลย [angry2-watermelon]
[smiling-tongue] 555 ก็ถามดูไปอย่างนั้นเองแหละ ครับ คงไม่เปลี่ยนแล้วล่ะครับ ของเตรียมจะครบหมดแล้ว ขืนเปลี่ยนไปเปลื่ยนมา
บานกันพอดี [yellow-lol] ว่าแต่หลอด อีเบย์ เพื่อผมหรือยังนาาาา [confused-face] หลอดทรงไข่ไก่ตัวผู้ก็สวยดี น่าสนนะครับ [happy-dreaming]
-
EL34 (6CA7) Class B Push-Pull
([url]http://tube-amps.net/images/EL34_PP_01/EL34_Schematic.jpg[/url])
Harmonic Distortion
([url]http://tube-amps.net/images/EL34_PP_01/EL34_HD.jpg[/url])
Frequency Response
([url]http://tube-amps.net/images/EL34_PP_01/EL34_FR.jpg[/url])
Common grid No. 2 resistor (without decoupling) 750 Ohms
Grid No. 1 bias -36 Volts
Grid No. 3 voltage 0 Volts
Input voltage 25.8 Volts
Load resistance, plate to plate 4000 Ohms
Plate supply voltage 500 Volts
Plate voltage 475 Volts
Grid No. 2 supply voltage 400 Volts
Plate current 2 x 125 mA
Grid No. 2 current 2 x 25 mA
Max. signal power output 70 Watts
Total harmonic distortion 5%
เรียนถามครับ
ดูวงจรตรงจุดไหน อย่างไร ถึงจะทราบว่าเป็นวงจร Class B ครับ
ขอบคุณครับ
-
ลองลาก load line ดูครับ Class B ก็จะเริ่มต้นจุด bias ตั้งแต่ 0 mA. ขึ้นไปเมื่อมีสัญญาณ แต่เ่ท่าที่ผมลองลากดูน่าจะจัดอยุ่ที่คลาส AB มากกว่าครับ ส่วนจะอยู่คลาสไหนก็ขึ้นอยู่กับว่าเราเป็นผู้กำหนดจุดไบอัสครับ อาจารย์ผมบอกว่าอย่าไปสนใจเลยว่ามันจะเรียกว่าอะไรเลยครับ สนใจแค่ว่าจะเลือกจุดที่มันจะสามารถทำงานได้เหมาะสมโดยไม่เกิดความเสียหายดีกว่าครับ จะเรียกว่า Class อะไรช่างมันเถอะบอกตรงๆผมเองก็อ่านมาเยอะ แต่ยิ่งอ่านเยอะแล้วก็ยิ่งงงเพราะยังไม่เจอคำตอบชัดเจนเลย แต่ที่นี่น่าจะได้คำตอบที่ชัดเจนขึ้นผมก้เพิ่งอ่านเหมือนกันครับ
http://www.valvewizard.co.uk/pp.html (http://www.valvewizard.co.uk/pp.html)
-
ตัดเอามาเฉพาะที่ตรงประเด็น
(http://www.valvewizard.co.uk/PushpullLoadline1.jpg)
The question is often asked; "what load do the valves 'see' in Class AB?". The answer lies in the name 'Class AB' - a combination of Class A and Class B.
While both valves are conducting the amplifier operates in Class A, and both valves 'see' a load of ½ the anode-anode impedance of the transformer (1/2 Za-a). However, as soon as one valve cuts off, that half of the transformer's primary is no longer part of the circuit. Because the impedance ratio is the square of the turns ratio, the load presented to the remaining 'on' valve must be only ¼ Za-a. So the stage operates in Class B at higher signal levels. Drawing a load line to show this is simple:
First draw a load line corresponding to ¼ Za-a. In this case that is ¼ 8k = 2k. This is the Class B part of the load [blue line in the image above].
This line may pass above the 'knee' of the grid curves for triode-like operation (good for hifi).
It may pass through the knee, which gives maximum power efficiency and is what the textbooks will tell you to do.
It may slightly pass below the knee. This is typical of guitar amps, but we must ensure that, during operation, the screen voltage can 'sag' so that as the operating point moves towards the left, the grid curves are pulled down so the line ends up passing through or above the knee. 1k screen stopper resistors are normally sufficient to acheive this.
If your line passes a long way below the knee, then the screen voltage must be lowered, or a very sizeable screen-grid stopper must be used. See the section on the pentode on how to do this. This load line may cross the max dissipation curve over a portion of its length- this is allowable.
Second, draw a load line corresponding to ½ Za-a. In this case it is ½ 8k = 4k. This is the Class A part of the load [purple line]. But as it stands, we appear to have biased the stage just to the point of cut-off, so it is only Class B.
(http://www.valvewizard.co.uk/PushpullLoadline2.jpg)
-
ขอบคุณ คุณเล็กครับ
ผมก็พยายามทำความเข้าใจ อ่านที่เค้าอธิบาย แต่ไม่เข้าใจสักที ครับ